Buy Makita MAC5200 Big Bore 3.0 HP Air CompressorMakita MAC5200 Big Bore 3.0 HP Air Compressor Product Description:
- Folding handle: Low profile for easy storage with handle folded
- Rugged wheels: Job-site portability; One-year manufacturer's warranty
- Built-in storage compartment; Conveniently stores air fittings and accessories
- Air hose wrap: Stores 50 feet of 3/8-inch air hose with handle folded or upright
- 120V; 13.8 Amps and 1800 watts
Product Description
Power and performance to run two framing nailers. Contractor air compressor features a low profile for easy storage (with handle folded), rugged wheels for jobsite portability, cast iron cylinders, industrial air filter, thermal overload protection and more. Pump: Oil-lubricated, cast iron, Duty Cycle: 50%, Max. PSI: 140, Motor Phase(s): Single, Dimensions L x W x H (in.): 30 x 20 1/2 x 21, Amps: 13.8, CFM at 90 PSI: 6.5, Tank Type: Horizontal, HP: 3, Air Tank Size (gal.): 5.2, Air Outlet Size (in.): 1/4, Volts: 115, Stage: Single, CFM at 40 PSI: 6.9, Working Pressure (PSI): 110-140, Portable or Stationary: Portable, Noise Level (dB): 90
Customer Reviews
Most helpful customer reviews
59 of 60 people found the following review helpful.
good performer, but
By Quick Smart
I agree with the wheel gripes. The wheels are injection molded with a very thin plastic, one of mine had a slash in it and collapsed on first use.So, I went up to farm and fleet and bought two new wheels with steel center and solid rubber, heavy tread, put them on and it is perfectly mobile over any terrain, now.I also agree Makita fudges on the specs.Most important though is the performance in use, and there, it shines. I've used similar double tank units from other manufacturers and much prefer the design of this unit. It stores connectors and a hose, handle breaks down for storage/transport, It is made very well and is quiet for a unit this size.It does draw power on the initial kick on, as they all do. I'd hoped to run this on my Yamaha 2500 watt generator, which is equivelant to a 20 amp circuit, but no go. It blows the breaker everytime. And the Yamaha runs a portable DeWalt table saw, jet 1200cfm dust collector and a chop saw just fine (not all at the same time!)So, while it is not perfect, it is a good performer and I'm very satisfied with the comressor at the cost.
35 of 35 people found the following review helpful.Item is not 1720 RPM as described
By Shop Foreman
Amazon's description describes this as running at 1720 RPM which is equal to Makita's MAC2400 product which runs at half this one's speed (and is quieter as a result).NOTE THIS ITEM RUNS AT 3420 RPM AND HAS A SLIGHTLY LARGER BORE THAN THE MAC2400 - SO EXPECT IT TO BE SIGNIFICANTLY LOUDER.
47 of 50 people found the following review helpful.
Makita Products & ESP. Service Down the Tubes
By Fit'n Fifty
I purchased this tool in June, 2008. It arrived from Amazon in perfect condition. After the initial 'break-in' period I used it a few times for minor chores around the shop. No problems. The problems began when I took it outside. For a machine this heavy it has lousy plastic wheels which not only bent out of shape, the axle they ride on also bent. I am not abusive with my tools and take reasonable care when handling them. Also, one of the plastic gauge covers cracked. In addition, the plastic shroud that goes over the compressor rattles like crazy and probably makes twice as much noise as this machine needs to make. Simply an observation of mine of poor design. But the real problem was the way in which Makita service treats you when you need help. The parts to replace were simple to swap out, and relatively inexpensive. The service rep I spoke with wanted me to drive this compressor 60 miles each way to have an authorized service center look at them to determine whether they "really failed" or not. In the past if I had a problem with heavy equipment that was easily repaired at my end the parts would be shipped free of charge, assuming the item was under warranty (it is). The rep further argued with me that the wheels simply "wore out" from usage. I explained to him I hadn't used this tool for more than a total of 20 hours and that that was an unreasonable assumption regarding the wheels. His next argument was that "Makita only warrants the motor on these tools and the rest is up to me - at my expense, to have repaired." Unbelievable. The warranty clearly states the entire tool is warranted for one year. Makita's have always made good tools in the past, but I would strongly recommend you look elsewhere if considering this tool, or any other from Makita. Their service center is abysmal. I can understand them not having the sharpest tacks handling the phone calls. But at least know your products and their respective warranties. No more Makita tools in this shop. This was a poor choice on my part.
Latest Price: See on Amazon.com!
More Info: See on Amazon.com!
See Customers Review: See on Amazon.com!
