Best Reviews of Swagman XC Cross-Country 2-Bike Hitch Mount Rack (1/1/4 and 2-Inch Receiver)

Swagman XC Cross-Country 2-Bike Hitch Mount Rack (1/1/4 and 2-Inch Receiver)Buy Swagman XC Cross-Country 2-Bike Hitch Mount Rack (1/1/4 and 2-Inch Receiver)

Swagman XC Cross-Country 2-Bike Hitch Mount Rack (1/1/4 and 2-Inch Receiver) Product Description:



  • Carries up to two bikes; fits 1/1/4 and 2-inch receiver
  • Features adjustable quick-release tire hoops and a ratcheting top arm which allows you to carry a wide variety of bike frames
  • Top arms fold down and the base folds up to keep this rack out of the way when not in use
  • Frame grip arms have a soft-frame coating to protect your bike's finish
  • Requires minimal assembly

Product Description

Transports up to 2 bikes. Compatible with 1 1/4" and 2" receiver hitch. It has a built in anti-woble hitch device. Upright ratchedt arms easily adjust to different bike frame sizes. It will accomodatge bike framse up to 59cm. The center arm folds down to allow acccess to the rear of the vehicle without removing the rack. Fits 20: to 29" tire sizes. Locking hitch pin required by the manufacturer is item No. 64029.

Customer Reviews

Most helpful customer reviews

113 of 115 people found the following review helpful.
5Bike Rack Exceeds Expectations.
By Kay E. Rigg
This rack is advertized as easy to put together out of the box, and easy to use once you are ready to to ride. Both of these statements are completely true. We have one man's and one woman's comfort bikes and the different length center main clamps of the rack are perfectly suited to these differences in bike design. The rack is very easy to insert and lock into our trailer hitch and the bikes are extremely easy to load requiring only a minimal lift and support to set and lock them into the rack. Definitely truth in advertising!

94 of 96 people found the following review helpful.
4Awesome value for the buck!
By Christopher Erickson
After shopping around everywhere on-line, including the classified and auction sites, this was the best deal in a reliable bike rack I could find. Combined with free shipping, it ended up being less than half of the price of the alternatives! This rack is really solid and very quick to take the bikes on and off. It is especially nice that the vertical bar can be rotated flat. This allows quick and painless access into the back of hatchback vehicles without having to remove the rack. A lot of good engineering thought went into this device.There are two minor points that prevent this item from having five stars. First, beware of the ratcheting top clamps, as they can be a real finger pincher if you are not careful. Second, even though the rack goes together painlessly and quickly, it would be better if the documentation discussed the more subtle but nice features and the best ways of loading and using the rack. For example it is important that the chain side of the two bikes face away from the center post, otherwise there is a clearance problem getting both bikes to fit. Another is the best way to load the first bike (remove both top clamps and rotate the vertical bar down to the back tire position). And yet another is the best approach for optimum positioning of the tire rings (keep all four loose until everything fits, no rubbing points exist and the bikes are centered behind the vehicle).All in all a great and solid product that will certainly outlast the bicycles it will be hauling around!-Christopher Erickson

67 of 71 people found the following review helpful.
5Outstanding Value and Features
By ShopSmart
Bought on Amazon. Best price anywhere by far. Goes together in a snap and what I really like is how it folds up for easy storage. I can take it off the hitch and stow it in the vehicle when I am off riding. I like the way it supports the bike from below as opposed to having bikes hanging by their frames. Well thought out design, and even the locking (clevis pins) are attached by a small cable to keep from loosing them. Swagman sells an extension to add two more bikes if you need it. I only carry one bike, and have room to carry a second if someone wants to join me on a ride. I highly recommend this carrier.

See all 375 customer reviews...


Latest Price: See on Amazon.com!
More Info: See on Amazon.com!
See Customers Review: See on Amazon.com!

Buy Swagman XC Cross-Country 2-Bike Hitch Mount Rack (1/1/4 and 2-Inch Receiver)

Deals for Mechanix Wear MHH-05-011 Mechanix Happy Hour Glove, Black, X-Large

Mechanix Wear MHH-05-011 Mechanix Happy Hour Glove, Black, X-LargeBuy Mechanix Wear MHH-05-011 Mechanix Happy Hour Glove, Black, X-Large

Mechanix Wear MHH-05-011 Mechanix Happy Hour Glove, Black, X-Large Product Description:



  • Glove is combination heat sleeve for engine tuning and tear down protection
  • Leather re-inforced panels on finger tips, thumb and palms for reduced wear and increased protection
  • Durable heat sleeve protects finger and forearm from burns
  • Two-way stretch spandex top
  • Narrow elastic cuff for added comfort

Product Description

Mechanix Wear Happy Hour gloves are the choice when heat resistance is a must. These race-inspired gloves provide a heat and tear-resistant Kevlar 18in. sleeve and fingers, stretch Cordura finger gussets and a second layer palm patch. These hard working gloves keep you covered from your fingers to your elbow. Size: XL, Material: Two way stretch spandex, Pairs (qty.): 1, Palm Material: Durable, heat-resistant cowhide

Customer Reviews

Most helpful customer reviews

0 of 0 people found the following review helpful.
5Two in One
By R. Bailey
Great gloves, I have the sleeves and some of the Carbon X 10 gloves which are good, however the happy hour do both in a single item for me.Also check out the sizing chart to make sure you get the best fit.[...]As far as I am concerned the ability to get different sizes is one of the top points of Mechanix and you keep a lot more dexterity because of it.

0 of 0 people found the following review helpful.
4best gloves ever
By W. tartt
i love these gloves. i work at an oil change shop. and these gloves have protected my arms and hands from getting burned many times. the one thing i don't like about these gloves is that when the glove gets oil on them it makes them very slippery and hard to hold the oil filters or tools. but other than that they are the best gloves i have ever owned

See all 2 customer reviews...


Latest Price: See on Amazon.com!
More Info: See on Amazon.com!
See Customers Review: See on Amazon.com!

Buy Mechanix Wear MHH-05-011 Mechanix Happy Hour Glove, Black, X-Large

Sale IRWIN Strait-Line 2035107 96-Inch Box Beam Level

IRWIN Strait-Line 2035107 96-Inch Box Beam LevelBuy IRWIN Strait-Line 2035107 96-Inch Box Beam Level

IRWIN Strait-Line 2035107 96-Inch Box Beam Level Product Description:



  • Continuous Edge Center Vial
  • Rugged Box Beam Construction
  • Patented Keyed Insert System
  • Machined Acrylic Vials
  • Patented Hex Key Calibration and Easy to Read Plumb View

Product Description

"IRWIN" NON MAGNETIC BOX BEAM LEVEL

* 96" Non-Magnetic Box Beam Level
* Extremely Accurate With Machined Acrylic Vials
* That Are 2 Times As Accurate As Standard Tube Vials
* Vials Are Guaranteed To Never Break, Leak
* Fade Or Fog, Extremely Durable With Continuos Edge Center Vial To Prevent Bending
* High Impact Rubber Endcaps Able To Withstand A 2 Story Fall
* Rugged Box Beam Construction Guaranteed Not To Bend
* Extremely Convenient With Plumb View Window
* Patented Keyed Insert System & Non-Slip Hand Grips.

Customer Reviews

Most helpful customer reviews

0 of 0 people found the following review helpful.
5Great tool
By Richard J. Flores
I have one of these at work so I am very happy with it, I used it for a garden wall made out of brick, the lenght was perfect.

See all 1 customer reviews...


Latest Price: See on Amazon.com!
More Info: See on Amazon.com!
See Customers Review: See on Amazon.com!

Buy IRWIN Strait-Line 2035107 96-Inch Box Beam Level

Price Compare IRWIN Strait-Line 2035105 72-Inch Box Beam Level

IRWIN Strait-Line 2035105 72-Inch Box Beam LevelBuy IRWIN Strait-Line 2035105 72-Inch Box Beam Level

IRWIN Strait-Line 2035105 72-Inch Box Beam Level Product Description:



  • Continuous Edge Center Vial
  • Rugged Box Beam Construction
  • Patented Keyed Insert System
  • Machined Acrylic Vials
  • Patented Hex Key Calibration and Easy to Read Plumb View

Product Description

Box Beam Level, Aluminum, Length 72 In, Total Number of Vials 3, Plumb Vials 2, Level Vials 1, Vial Material Acrylic, Block Vial Type, Accuracy 0.0005 In/In

Customer Reviews

Most helpful customer reviews

1 of 1 people found the following review helpful.
5Long and Strong
By Andrew
This is a great level for handyman use. I recently replaced some doors and this level was the perfect tool. It is not too heavy given its size and the floats are easy to read.The one project this level is perfect for is installing sliding glass doors and large windows. This level can clear the whole span of glass and measure the actual frame. With a sliding door this is important because it is the frame and not the glass that controls how well a door slides open and close.

0 of 0 people found the following review helpful.
5must be good
By dusty jack
This level must be good. UPS stole it from me, delivering an empty box. Then they refunded my money.

See all 2 customer reviews...


Latest Price: See on Amazon.com!
More Info: See on Amazon.com!
See Customers Review: See on Amazon.com!

Buy IRWIN Strait-Line 2035105 72-Inch Box Beam Level

Low Price Irwin 274108 Vise Grip 6-Inch Jaw Capacity 48-Inch Cast Iron Pipe Wrench

Irwin 274108 Vise Grip 6-Inch Jaw Capacity 48-Inch Cast Iron Pipe WrenchBuy Irwin 274108 Vise Grip 6-Inch Jaw Capacity 48-Inch Cast Iron Pipe Wrench

Irwin 274108 Vise Grip 6-Inch Jaw Capacity 48-Inch Cast Iron Pipe Wrench Product Description:



  • Drop Forged Jaw
  • Heavy Duty Cast Iron Housing
  • I-Beam Handle
  • Easy-Spin Adjustment Nut
  • Hammerhead

Product Description

586-274108 Features: -Hardened teeth provide tremendous bite.-Easy spin adjusting nut is heat treated for durability.-Material: Cast Iron.-Price is for 1 Each.

Customer Reviews

Most helpful customer reviews

0 of 0 people found the following review helpful.
5Big Pipe Wrench
By Hal
The wrench appears to be a well-made quality product. I needed a large capacity wrench to loosen end caps on hydraulic cylinders. This wrench did the job. I used a 10 foot cheater bar and “bounced” on the end of the bar to loosen the end caps. The jaws of the wrench “bit” into the end cap without any slipping. The wrench is rated as having a 6-inch capacity. Based on my measurements, this capacity could easily be "stretched" to 7 inches. The jaws are well machined and the adjustment nut turns smoothly. If you need a heavy-duty, large capacity, 35 lb. pipe wrench; this is an excellent choice.

0 of 0 people found the following review helpful.
4Great wrench for the money
By HotRod_Horror
The wrench works great and the nut is easy to turn and adjust the jaws. Although we'll see how easy it is after a few years of use. Overall it's a good wrench, it does it's job and is pretty beefy. The only downside to this wrench is that it is made in China.

0 of 0 people found the following review helpful.
5Awesome!
By System Builder
I work on gas drilling rigs in Pennsylvania. Having good tools are essential (they can help ensure your safety). This one has been wonderful. When I produced it to the crew they loved it immediately. It immediately out performed a Ridgid wrench of the same size.I recommend this tool.

See all 4 customer reviews...


Latest Price: See on Amazon.com!
More Info: See on Amazon.com!
See Customers Review: See on Amazon.com!

Buy Irwin 274108 Vise Grip 6-Inch Jaw Capacity 48-Inch Cast Iron Pipe Wrench

Price Comparisons of Hitachi NR90AC3 Round Head 2-3/8-Inch to 3-1/2-Inch Framing Nailer

Hitachi NR90AC3 Round Head 2-3/8-Inch to 3-1/2-Inch Framing NailerBuy Hitachi NR90AC3 Round Head 2-3/8-Inch to 3-1/2-Inch Framing Nailer

Hitachi NR90AC3 Round Head 2-3/8-Inch to 3-1/2-Inch Framing Nailer Product Description:



  • High capacity rear loading aluminum magazine for easy loading
  • Aggressive toe nailing for precision accuracy
  • Tool-less depth adjustment for adjustments on the fly
  • Ergonomically designed rubber grip for reduced operator fatigue
  • Drives all 3-1/2-inch by .162-inch true common nails for convenience

Customer Reviews

Most helpful customer reviews

21 of 21 people found the following review helpful.
5Some comments on the negatives
By Remodeling in SoCal
I own a NR90AC2,same gun but does not have a lever select on the trigger:On the 8d nail issue,in that size, I shoot ORCO brand,made in USA, in the gun, 2 3/8" ring shank Egalv. and never had a jam. Cheap off brand nails or the wrong angle=jams. 6d(2") nails are not for this gun. I always shoot ringshank into sheet goods b/c of the better grip. 6d's are not code here in CA anyway. The single fire AC2 issue, you need to change out the trigger, the included one is a NOT a single fire(sequential) and will easily double fire, it is a contact fire(bump) type. Change out the trigger and you can not double fire as was said. AC3 has a lever to change it, AC2 you have to change out the whole trigger assembly.This is an excellent gun ,drives into anything wood,but you have to use good quality nails and be aware of the trigger b/c it has a lot of power. I do not usually use bump fire, can be a safety hazard,waste of nails,inconsistent depths, but you even can bump fire one nail in the sequence mode, great feature on the AC3.11/09 update; Now using an AC3 with a skilsaw rafter hook added, I updated only because I like the easy flip trigger lever;still no issues with 8D's except I had 1 jam due to the plastic collation strip was doubled over from a partial strip stack,remove rear magazine bolt, remove jam, replace. Forgot to mention also using Grip Rite and Senco ring shank galv 3" are excellent for grip and can be used in PT lumber as well. Basically an all metal design, high quality ,made in Japan is just as good as it gets if you want a powerful well made framer that shoots CA code RH 16D 3.5" x 0.162. Still the best out there IF you do not use cheap off brand nails. And, it is not the alien ugly neon green on the now discontinued models. They have gone back to the classic pale green most prefer and idenify with hitachi air tools9/2010Totally disagree on review panning gun for sheathing. . Again I use this all the time for 8D, sheathing, etc. , and have only a very rare jam if you are working correctly. The reviewer who said this gun is not for sheathing is dead wrong. They either are not using quality nail strips and or are damaging the ends of the collation strips so the nails do not line up properly in the Mag. Senco;s 8D's if not damaged will not jam, period. Some are better off using a wire collated coil nailer which can hold way more nails and you can shoot wild machine gun style as a lot of track home laborers/builders do thinking they are laying down asphalt roofing and can put a nail anywhere because it only has to enter the sheathing. . Many of those nails shot like that in structural sheathing are shot into thin air missing the supporting lumber. Fails code, wastes money on materials and labor to fix if caught in inspection, or makes for a weak house.... if you are in a hurry , do not want to buy quaity nails, be precise in use and loading the mag. [as I often see people do] and being as fast as you can be to just get the job over-with as your main concern, this is not the gun for you. It will cause you to have the gun jam,

16 of 17 people found the following review helpful.
5Hitachi NR90AC3 Great Nailer
By R. Cervantes
Great Nailer, a little heavy but nicely balanced. I have been using this nailer about three months @ 10 hrs a day without any problem whatsoever. For heavy use, I recommend putting an automatic oiler in your air-line as that makes the tool perform much better than having to add a few occassional drops.The manual states that the minimum nail size is 2-3/8 (ca 8d); though the factory literature and on-line advertising says that the minimum is 2". I am using 8d nails, so I am not sure about the lower limit. However, for those wanting to use nails smaller than 8d, I would recommend talking to an experieced retailer about the product capabilities. It is not an inexpensive tool, so make sure it does what you want.

6 of 7 people found the following review helpful.
3Doesn't shoot all nails
By E. Underwood
We Purchased the NR90HitachiAC3 because we liked the Hitachi83 that we had for years, but didn't have an adjustment for the nail depth. They advertise that it shoots nails from 8's to 16's. The bigger nails, it shoots fine with not much kick back. Doesn't jam on them. The 8's are a nightmare. That is the main reason that we bought the gun for the 8's as we wanted to be able to adjust the depth while doing the sheathing for all the required engineering. The nails either jam or the slide slips by the nails. Not just a few times, but every time.If you are buying this gun for shooting 10's or 16's then it is a fine gun. If you want it for nailing the shear walls with 8d's... forget it, it is a waste of time and money.

See all 9 customer reviews...


Latest Price: See on Amazon.com!
More Info: See on Amazon.com!
See Customers Review: See on Amazon.com!

Buy Hitachi NR90AC3 Round Head 2-3/8-Inch to 3-1/2-Inch Framing Nailer

For Sale Online Hitachi NR83A2(S) Round Head 2-Inch to 3 1/4-Inch Framing Nailer (without Depth Adjustment)

Hitachi NR83A2(S) Round Head 2-Inch to 3 1/4-Inch Framing Nailer (without Depth Adjustment)Buy Hitachi NR83A2(S) Round Head 2-Inch to 3 1/4-Inch Framing Nailer (without Depth Adjustment)

Hitachi NR83A2(S) Round Head 2-Inch to 3 1/4-Inch Framing Nailer (without Depth Adjustment) Product Description:



  • Framing nailer with top-loading, two-piece magazine
  • Selective trigger actuation; 2 to 3-1/4 inch capacity
  • Weighs just 7.9 lbs
  • Rubber grip for comfort
  • 1-year warranty
  • Comes with a 5-year limited warranty
  • Fires plastic-coated, full round head nails from 2-inches to 3-1/4-inches
  • Open nose design for easy extraction of a jammed nail
  • Rubber grip for superior control and comfort during use
  • Selective actuation allows transition from sequential nailing to bump-fire with ease

Product Description

Hitachi NR83A2S 3-1/4-Inch Plastic Strip Collated Framing Nailer

Customer Reviews

Most helpful customer reviews

6 of 6 people found the following review helpful.
5It's a HITACHI
By olajoe
This gun is awesome. It's fast, lightweight, and the bump mode let's you move right along without having to wait. The gun also responds well to the pressure regulator, no need for a depth gauge here. If you're concerned more about safety and want sequential fire this has that option w/turn of a ring. If I need another nail gun, this will be it.

0 of 0 people found the following review helpful.
5best nailgun ever
By wmwalker
This is the best framing gun made i build houses for a living and no other gun stacks up to this one in speed and reliability

0 of 0 people found the following review helpful.
5Hitachi Air Nailer
By J. Flammer
I find this a great product, I have used two other types of air nailers in the past and they were okay however of all the construction sites I've been on I mostly see these Hitachi Air Nailers in use that is why I bought this one.

See all 6 customer reviews...


Latest Price: See on Amazon.com!
More Info: See on Amazon.com!
See Customers Review: See on Amazon.com!

Buy Hitachi NR83A2(S) Round Head 2-Inch to 3 1/4-Inch Framing Nailer (without Depth Adjustment)